丁基膠打膠機是出產中空玻璃的首要必要設備。這是一種半自動帶材涂布機，通過手動抓住鋁制距離框來操作。將鋁制距離架放在傳送帶上，并手動抓住鋁制距離架沿傳送帶運行。當鋁制距離框通過傳感器時，轉印壓力輥和膠水閥將依據設置程序自動運行，即氣缸將起作用，壓力輥將被壓下。按下鋁制距離架以跋涉。當鋁制距離架抵達膠頭時，涂上膠水。將膠水均勻地涂在鋁制距離架上。當墊片框架的另一側行將抵達壓力輥時，壓力輥將被抬起并向左移動。使用橡膠頭時，橡膠閥將自動中止。
Butyl glue beater is the primary necessary equipment for producing insulating glass. This is a semi-automatic strip coater, which is operated by manually grasping the aluminum distance frame. Place the aluminum distance frame on the conveyor belt and manually grasp the aluminum distance frame to run along the conveyor belt. When the aluminum distance frame passes through the sensor, the transfer pressure roller and glue valve will operate automatically according to the setting program, that is, the cylinder will work and the pressure roller will be pressed down. Press the aluminum distance rack to trek. When the aluminum distance frame reaches the rubber head, apply glue. Apply the glue evenly to the aluminum distance frame. When the other side of the gasket frame is about to reach the pressure roll, the pressure roll will be lifted and moved to the left. When the rubber head is used, the rubber valve will stop automatically.
丁基膠打膠機常見問題的解決方案：
Solutions to common problems of butyl glue applicator:
1.鋁框的一側或兩邊沒有膠水時，首要，應查看橡膠筒和橡膠頭的溫度是否正常，壓力是否在我們設定的范圍內。查看兩個橡膠頭之間的距離是否太大。
1. When there is no glue on one or both sides of the aluminum frame, first of all, check whether the temperature of the rubber cylinder and rubber head is normal and whether the pressure is within the range set by us. Check whether the distance between the two rubber heads is too large.

假如在上述情況下沒有問題，則可以得出結論，丁基膠中的雜質堵塞了兩個膠頭(或一個)，而且膠頭的眼睛被堵塞。這需求卸下膠頭并用煤油浸泡。然后清洗膠頭中的一切膠，然后重新安裝。
If there is no problem in the above case, it can be concluded that the impurities in butyl rubber block two rubber heads (or one), and the eyes of the rubber head are blocked. This requires removing the rubber head and soaking it in kerosene. Then clean all the glue in the rubber head and reinstall it.
2.丁基橡膠涂布機該設備采用液壓體系。油缸和液壓體系均通過高壓油管連接。每個連接均通過組合墊密封。假如發現漏油，請及時更換組合墊。
2. Butyl rubber coater the equipment adopts hydraulic system. The oil cylinder and hydraulic system are connected through high-pressure oil pipe. Each connection is sealed by a combination gasket. If oil leakage is found, please replace the combination pad in time.
3.設備的膠頭加熱和膠筒加熱由兩個加熱棒和一個加熱板提供，溫度由溫度控制儀設定和調節。假如溫度升高不高或升高后下降，請查看加熱棒或加熱板是否損壞，并查看溫控表是否正常。
3. The rubber head heating and rubber cylinder heating of the equipment are provided by two heating rods and one heating plate, and the temperature is set and adjusted by the temperature controller. If the temperature does not rise high or decreases after rising, please check whether the heating rod or heating plate is damaged and whether the temperature control meter is normal.
雙組份打膠機為您提供了以上的精彩內容，更多的精彩內容請點擊進入我們的網站：http://www.txxfj.com我們后續會有更多的內容等您查看。
The two-component glue applicator provides you with the above wonderful contents. For more wonderful contents, please click to enter our website: http://www.txxfj.com We will have more content for you to check later.