丁基膠涂布機出現故障，可能會導致整個中空玻璃的進程停滯。而丁基膠涂布機是相對簡單的中空玻璃設備，康捷機械為您介紹一下丁基膠涂布機的常見故障，以及遇到類似故障處理的方法。
The failure of butyl rubber coating machine may cause the process of the whole insulating glass to stop. Butyl rubber coating machine is a relatively simple insulating glass equipment. Kangjie Machinery will introduce you the common faults of butyl rubber coating machine and the methods for handling similar faults.
丁基膠涂布機擠出的丁基膠是毛刺不光滑時，如果是新設備，應先觀察出膠孔是否光滑，如果出膠孔粗糙，應先打磨，再試機器；舊機器，可能顯示的溫度與實際的不相符，這時就需要將溫度進行上調，直到出膠正常即可；
When the butyl adhesive extruded by the butyl adhesive coater is not smooth, if it is a new equipment, observe whether the glue hole is smooth. If the glue hole is rough, polish it first, and then try the machine again; For the old machine, the displayed temperature may not be consistent with the actual temperature. At this time, it is necessary to increase the temperature until the glue is discharged normally;
丁基膠涂布機打出的膠粘不到鋁隔條上時，可能是原因還是溫度過低，與膠要求的溫度不太符合，只需要咨詢丁基膠提供方需要的溫度，將溫度調整合適即可；

When the adhesive produced by the butyl adhesive coater cannot reach the aluminum spacer strip, the most likely reason is that the temperature is too low, which is not in conformity with the temperature required by the adhesive. Just consult the butyl adhesive supplier for the required temperature and adjust the temperature properly;
丁基膠涂布機出現膠頭漏膠，膠頭下面是硅膠墊，估計是硅膠墊損壞導致的，只需要更換硅膠墊即可，但是，需要提醒的是，擠膠壓力過大才是導致硅膠墊損壞的根本原因，不建議將擠膠壓力調的過大；
The rubber head of the butyl rubber coating machine leaks, and the rubber head is under the silicone pad. It is estimated that the damage of the silicone pad is the cause. It is only necessary to replace the silicone pad. However, it should be reminded that the excessive extrusion pressure is the root cause of the damage of the silicone pad, and it is not recommended to adjust the extrusion pressure too much;
丁基膠涂布機的膠頭或膠缸不加熱，估計是加熱棒損壞，更換即可；
The rubber head or rubber cylinder of the butyl rubber coater is not heated. It is estimated that the heating rod is damaged, and it can be replaced;
丁基膠涂布機的傳送皮帶跑偏，這個應該算不得故障，只需要調整四個角的皮帶輪即可；
The conveyor belt of the butyl rubber coating machine deviates, which should not be considered as a fault. It only needs to adjust the pulley at four corners;
丁基膠涂布機的顯示屏不亮，可以正常使用。這可能是顯示屏損壞或者顯示屏供電線出現問題，更換即可；
The display screen of butyl adhesive coater is not bright and can be used normally. This may be because the display screen is damaged or the power supply line of the display screen is faulty. Replace it;
本文由臥式丁基膠涂布機友情奉獻.更多有關的知識請點擊:http://www.txxfj.com真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待
This article is dedicated by the horizontal butyl adhesive coater. For more information, please click: http://www.txxfj.com Sincere attitude. We will provide you with comprehensive services. We will continue to offer you more relevant knowledge. Please look forward to it