在使用玻璃打膠機的過程當中會遇到各種各樣的問題，那么臥式玻璃打膠機的中空膠拉斷時間不正常了怎么辦呢？下面我們來一一向您介紹。
Various problems will be encountered in the process of using the glass gluing machine. What if the hollow glue breaking time of the horizontal glass gluing machine is abnormal? Now let's introduce to you one by one.
一般致斷中空膠拉斷時間過長過短的時間一般主要是由以下四類原因所引起的：環境溫度偏高會導致拉斷時間變短，環境溫度偏低會導致拉斷時間延長；環境濕度過低也會導致拉斷時間有所延長。解決方法：采取空調、暖房、曬水等方法讓使用環境和養護環境的溫濕度在合適范圍內。
Generally, the breaking time of hollow glue is too long and too short, which is mainly caused by the following four reasons: the high ambient temperature will lead to the shortening of the breaking time, and the low ambient temperature will lead to the prolongation of the breaking time; Too low ambient humidity will also lead to an extension of the breaking time. Solution: adopt air conditioning, greenhouse, water drying and other methods to keep the temperature and humidity of the use environment and maintenance environment within the appropriate range.
B組份比例太高會導致拉斷時間變短，B組分比例偏低會導致拉斷時間延長。解決方法：調節中空膠的A、B組分配比使其在中空膠制造商要求的范圍內。
Too high proportion of component B will shorten the breaking time, and too low proportion of component B will prolong the breaking time. Solution: adjust the distribution ratio of group A and group B of hollow rubber to make it within the range required by the hollow rubber manufacturer.

夏季配方的膠在冬季使用時，環境溫度下降，拉斷時間會偏長；而冬季配方的膠在夏天使用，由于環境溫度上升，拉斷時間會縮短。解決方法：冬、夏季用膠時盡量選用相對應季節配方的中空膠。
When the glue formulated in summer is used in winter, the ambient temperature decreases and the breaking time will be too long; The glue formulated in winter is used in summer, and the breaking time will be shortened due to the rise of ambient temperature. Solution: when using glue in winter and summer, try to use hollow glue with corresponding seasonal formula.
污染物的影響。比如打膠機之前使用的是其他類型或其他的中空膠，換膠后由于打膠機清洗不干凈，拉斷時間會有影響。尤其是打膠機之前使用的是聚硫膠，換用硅酮膠，如果打膠機沒有完全清洗干凈，拉斷時間會明顯變長。解決方法：換膠時，一定要將打膠機及管道清理干凈；尤其是之前使用的是聚硫換用硅酮膠，一定要將設備所有物料流道相關部件完全拆卸，用合適的溶劑完全將殘余物料清洗干凈，即使很少量的聚硫膠殘余都會造成硅酮膠的拉斷時間明顯延長。
Impact of pollutants. For example, the glue applicator used hollow glue of other types or brands before. After changing the glue, the breaking time will be affected due to the unclean cleaning of the glue applicator. In particular, polysulfide glue is used before the gluing machine, and silicone glue is used instead. If the gluing machine is not completely cleaned, the breaking time will be significantly longer. Solution: when changing the glue, be sure to clean the glue applicator and pipeline; In particular, the previous use of polysulfide is to replace silicone adhesive. All relevant parts of the material flow path of the equipment must be completely disassembled and the residual materials must be completely cleaned with appropriate solvent. Even a small amount of polysulfide adhesive residue will significantly prolong the breaking time of silicone adhesive.
本文的精彩內容由中空玻璃丁基膠涂布機提供知識提供，本網站還有很多的精彩內容，更多的內容您可以點擊進入：http://www.txxfj.com我們有專門的客服為您解答問題
The wonderful content of this article is provided by the insulating glass butyl adhesive coater. There are many wonderful contents on this website. You can click to enter more contents: http://www.txxfj.com We have special customer service to answer your questions