業界將膠水按粘料特點分為動物膠、植物膠、無機物及礦藏、組成彈性體、組成熱塑性資料、組成熱固性資料、熱固性、熱塑性資料與彈性體復合幾種。比較常見的AB膠水、瞬間膠、厭氧膠水、UV膠水及一些特別膠水。
The industry divides glue into animal glue, vegetable glue, inorganic substance and mineral deposit, elastomer, thermoplastic material, thermosetting material, thermosetting material, thermoplastic material and elastomer composite. More common AB glue, instant glue, anaerobic glue, UV glue and some special glue.
膠水在運用過程中，要確定的是膠水份額。比方AB膠水，將主劑與硬化劑按1:1的份額混合，在保證被凃物表面清潔之后再將膠水涂抹至被涂物。將溫度控制在六十度到九十度為佳。瞬間膠在運用過程中經常遇到白化，脆性大，不耐老化的問題。運用前好先做試驗，保證膠水的粘結能夠到達預期效果。厭氧膠就是缺氧膠，可用于粘接也可用于密封。厭氧膠因其具有共同的厭氧膠固化特性，可運用于鎖緊、密封、固持、粘接、堵漏等方面。厭氧膠已成為機械職業不行短少的液體東西。在航空航天、軍工、汽車、機械、電子、電氣等職業有著很廣泛的運用。
In the course of using glue, the glue share must be determined. For example, AB glue, mix the main agent and hardener in a 1:1 ratio, and then apply the glue to the coating after ensuring that the surface of the object is clean. The best way to control temperature is from sixty degrees to ninety degrees. During the use of instant adhesive, whitening, brittleness and ageing resistance are often encountered. It is better to do experiments before making use of the glue so as to ensure the glue can reach the expected effect. Anaerobic adhesive is anoxic glue, which can be used for bonding and sealing. Anaerobic adhesives have the same curing characteristics of anaerobic adhesives, which can be used in locking, sealing, fixing, bonding, leak plugging and so on. Anaerobic adhesive has become a liquid substance that can not be short of mechanical occupation. It has been widely used in aerospace, military, automobile, machinery, electronics, electrical and other occupations.

UV膠水。UV是英文Ultraviolet Rays的縮寫，因此UV膠水又叫做紫外線膠。由于UV膠水的特別性，往往還要配合UV點膠針筒進行點膠作業。由于它的無污染，無溶劑，因此廣泛運用于各個點膠作業。還有一些特別膠水，如貓眼膠，鉆石膠，以及一些職業專用膠水，如手表專用膠水。
UV glue. UV is the abbreviation of English Ultraviolet Rays, so UV glue is also called UV glue. Because of the special characteristics of UV glue, UV dispensing syringe is often used for dispensing operations. Because it is non polluting and solvent free, it is widely used in dispensing operations. There are also some special glues, such as cat's eye glue, diamond glue, and some professional glue, such as watch glue.
打膠過程中的幾個小注意點：
Several small points in the process of glue making:
1.很多膠水（比方一些瞬間膠）的氣味都很沖鼻，所以要在保證點膠作業在一個通風的工作環境下進行。
1. A lot of glue (e.g. instant glue) smells nasal, so make sure that dispensing is done in a ventilated working environment.
2.除非是點膠需求，不然不要將不同的膠水混合裝于一個容器里。運用完膠水，將膠水放置于陰涼通風枯燥，且不易觸碰到的當地。擰緊膠蓋，防止膠體走漏。當有很多走漏時能夠用水固化后再刮除。
2. unless glue is needed, do not mix different glue in a container. After applying glue, place glue in a cool, ventilated, dry place that is not easy to touch. Tighten the rubber cover to prevent colloid leakage. When there are many leaks, it can be cured with water and then scraped.
3.操作時，記住要帶阻隔手套。假如不小心沾到手上，未干時應該用酒精查擦洗或許以溫肥皂水浸泡，用丙酮、解膠劑去除，不然等膠水干了今后，就只能用刀具進行膠水鏟除。假如觸及皮膚或眼睛，應先用清水沖刷然后用溫熱毛巾熱敷，之后當即就醫。
3. remember to wear gloves when operating. If accidentally dipped in the hands, not dry should be scrubbed with alcohol or soaked in warm soap water, acetone, glue removal, or other glue dry in the future, you can only use a knife glue eradication. If you touch the skin or eyes, wash them with clean water and apply them with warm towels. See a doctor immediately afterwards.
濟南昌盛機械，對雙組份打膠機感興趣的朋友可以關注我們http://www.txxfj.com，敬請期待更多精彩內容。
Jinan Changsheng Machinery, the two-component glue beater interested in friends can pay attention to our http://www.txxfj.com, please look forward to more exciting content.