玻璃打膠機打膠不飽滿出現這個問題其實很簡單，主要是有以下幾種情況導致的！下面雙組份打膠機的小編就給大家分析一下吧！
The problem of insufficient gluing of glass gluing machine is very simple. It is mainly caused by the following circumstances. The following two-component glue machine knitting to give you an analysis of the bar!
一、打膠速度過快
1. Gluing speed is too fast
有的客戶為了加快自己的生產節奏追趕生產計劃，將打膠速度認為調整的過快，導致膠體還沒有完全達到合格標準機頭就已經移動到下一個位置進行打膠操作了。
Some customers in order to speed up their production rhythm to catch up with the production plan, the gluing speed is considered to be too fast to adjust, resulting in the colloid has not fully met the qualified standard head has moved to the next position for gluing operation.
如果我們需要加快打膠的速度調整了打膠機的移動參數的話，那么我們對應的也應該對供膠系統也進行相應的設置，比如這時候我們就需要加大供膠壓力，增大打膠機的出膠速度來配合對象的移動速度的增加。
If we need to speed up the gluing speed and adjust the moving parameters of the gluing machine, then we should also set up the gluing system accordingly. For example, at this time, we need to increase the pressure of the gluing machine, increase the speed of the gluing machine to match the increase of the moving speed of the object.
如果我們僅僅是單獨的增加了打膠機的移動速度而沒有對壓力進行調節的話就很有可能出現打膠不飽滿的情況發生。
If we simply increase the speed of the glue machine without adjusting the pressure, it is likely that the glue will not be full.
二、供膠壓力不足
2. Insufficient supply pressure
這個情況其實在前一種情況的已經進行過描述了，即便你沒有對打膠機的移動速度進行調節也出現了打膠不飽滿的情況，那么也有可能是供膠壓力過小導致的。這時候我們僅僅需要調整供膠壓力即可完美的解決這個問題的發生。

In fact, this situation has been described in the former case. Even if you do not adjust the speed of the glue machine, there is a situation that the glue is not full, then it may also be caused by too little glue supply pressure. At this time, we only need to adjust the supply pressure to solve this problem perfectly.
三、機頭感應器損壞
3. Damage of nose inductor
這種情況非常的少見，但是也不排除這種情況的發生。在我們的打膠機機頭有一個對鋁條深淺進行探測的感應器，如果發現鋁條過深或者過淺的時候他會自動的調整移動的移動速度以及供膠壓力（自動調整幅度是小范圍內的）。如果我們的鋁條本身就深淺不一，在加上我們的感應器損壞的壞就會發生這種情況！
This situation is very rare, but it can not be ruled out. There is a sensor to detect the depth of the aluminium bar in the head of our gluing machine. If it is found that the aluminium bar is too deep or too shallow, it will automatically adjust the moving speed and the gluing pressure (the automatic adjustment range is small). If our aluminium bars are different in depth, this will happen if our sensors are damaged.
感謝您的閱讀與觀看，本文的精彩內容來自：雙組份打膠機，我們會有更多的精彩內容繼續為您呈現，詳情請點擊：http://www.txxfj.com
Thank you for your reading and watching. The wonderful content of this article comes from: two-component glue beater. We will have more wonderful content to continue to show you. For more details, please click: http://www.txxfj.com.