膠條式中空玻璃的組裝對工藝的要求相比鋁條式中空玻璃的組裝對環境和濕度的要求是不一樣的。
The assembly of adhesive strip type insulating glass has different requirements on the environment and humidity than the assembly of aluminum strip type insulating glass.
膠條式中空玻璃組裝對環境的要求：膠條式中空玻璃加工溫度冬季應在10-20度之間，夏季應在20-30度之間為宜。
Environmental requirements for assembly of adhesive tape type insulating glass: the processing temperature of adhesive tape type insulating glass should be 10-20 ℃ in winter and 20-30 ℃ in summer.
膠條式中空玻璃組裝相對濕度的要求：因膠條式中空玻璃干燥劑呈粉末狀，與膠混合均勻后干燥劑發揮作用較慢，所以應保證膠條裝配區域相對濕度稍低。
Requirements for relative humidity of adhesive strip type insulating glass assembly: as the adhesive strip type insulating glass desiccant is in powder form, it will play a slow role after being mixed evenly with the adhesive, so it should be ensured that the relative humidity of the adhesive strip assembly area is slightly low.

鋁條式中空玻璃組裝在溫度上要求更高一些，相對濕度要求也更嚴格。
The assembly of aluminum strip insulating glass has higher requirements on temperature and relative humidity.
鋁條式中空玻璃組裝對環境的要求：溫度也應在10-30度之間
Environmental requirements for the assembly of aluminum strip insulating glass: the temperature should also be between 10-30 degrees
鋁條式中空玻璃組裝相對濕度的要求：此種中空玻璃對相對濕度的要求稍低一些，正常情況即可。但應注意的是，干燥劑應選擇正規廠家的合格產品，以保證干燥劑的有效使用。干燥劑開封后于二十四小時之內用完，因為聚硫膠的透氣性較大，密封性差，因此要采用雙道密封。用丁基膠作為第一道密封，起到陰隔氣體的作用。用聚硫膠作為第二道密封，主要作用是粘結作用，其次才是隔氣作用。實踐證明，單產密封的中空玻璃壽命只有5年左右，而雙道密封的中空玻璃壽命可長達20年甚至40年以上，因此，發展雙道密封中空玻璃是大勢所趨。
Requirements for relative humidity of aluminum strip insulating glass assembly: the requirements for relative humidity of this kind of insulating glass are slightly lower, which can be met under normal conditions. However, it should be noted that the qualified products of regular manufacturers should be selected to ensure the effective use of desiccants. The desiccant shall be used up within 24 hours after being unsealed. Because the polysulfide adhesive has high permeability and poor sealing performance, double sealing shall be adopted. Butyl rubber is used as the first seal to isolate gas. The polysulfide glue is used as the second seal, which is mainly used for adhesion, and then for gas separation. Practice has proved that the service life of insulating glass with unit production sealing is only about 5 years, while the service life of double sealing insulating glass can be as long as 20 years or even more than 40 years. Therefore, the development of double sealing insulating glass is the trend of the times.
以上就是為大家介紹的有關全自動鋁條折彎機詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.txxfj.com
The above is a detailed introduction to the automatic aluminum bar bending machine. I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude http://www.txxfj.com