中空玻璃膠機從功能上講，非常簡單。主要關注中空玻璃上膠，但中空玻璃上膠機在上膠過程中可能會遇到不完全上膠的問題。
Hollow glass glue machine is very simple in function. The main concern is the gluing of insulating glass, but the gluing machine may encounter the problem of incomplete gluing in the gluing process.
事實上，我們這個問題主要是由以下三個條件造成的!
In fact, our problem is mainly caused by the following three conditions!
1. 上膠速度太快
1. Glue application speed is too fast
一些客戶為了加快生產計劃在自己的生產節奏,調整密封劑認為太快,導致膠體的負責人還沒有完全達到合格標準的塑料運行到下一個地方,如果我們需要加速調整橡膠機運動參數,所以我們也要有相應的設置相應的膠水供應系統,如這一次我們需要增加供應壓力,增加膠速度,使上膠機隨物體移動速度增加。如果我們只增加膠水機的速度而不調整壓力，很可能是膠水不夠用。
In order to speed up the production schedule and adjust the sealant, some customers think it is too fast. As a result, the person in charge of the gel hasn't completely reached the qualified standard for the plastics to run to the next place. If we need to speed up the adjustment of the movement parameters of the rubber machine, we also need to set up the corresponding glue supply system. For example, this time, we need to increase the supply pressure, Increase the glue speed, so that the glue machine with the object moving speed increases. If we only increase the speed of the glue machine without adjusting the pressure, it is likely that the glue is not enough.

2. 供膠壓力不足
2. Insufficient glue supply pressure
事實上，這種情況已經在前一種情況下描述過了，即使不調整膠機的速度也會出現打膠不滿意的情況，那么有可能供應的膠壓力太小。此時我們只需要調整膠水壓力就可以巧妙解決這個問題。
In fact, this situation has been described in the previous situation. Even if the speed of the glue machine is not adjusted, there will be unsatisfactory gluing, so it is possible to supply too little glue pressure. At this time, we just need to adjust the glue pressure to solve this problem perfectly.
3.避免損壞傳感器
3. Avoid damaging the sensor
這種情況非常罕見，但不能排除。在我們的中空玻璃上膠機的頭部，有一個傳感器可以檢測鋁帶的深度。如果鋁帶過深或過淺，會自動調節移動速度和上膠壓力(自動調節范圍小)。這可能會發生，如果我們的鋁帶本身是一個不同的色調，加上損壞我們的傳感器!
This is very rare, but it cannot be ruled out. At the head of our insulating glass gluer, there is a sensor that can detect the depth of the aluminum strip. If the aluminum strip is too deep or too shallow, it will automatically adjust the movement speed and glue pressure (the automatic adjustment range is small). This can happen if our ribbon itself is a different tone, plus damage to our sensors!
以上就是雙組份打膠機對如何避免上膠不全的措施的詳細介紹，想要了解更多請點擊官網http://www.txxfj.com
The above is a detailed introduction of the two-component dispenser on how to avoid incomplete gluing. To learn more, please click http://www.txxfj.com