翻開氣泵開關，電源總開關，控制臺開關，在控制臺按手動按鈕，然后在顯現屏上找到原點設定，點擊輔助原點設定，然后點擊頭部原點設定，留意原點設定時防止頭部和輔助吸盤碰撞。等設定好然后返回找到玻璃厚度設定，先是玻璃的厚度然后是鋁隔條然后還是玻璃的厚度，輸入完以后，點擊設置進入。等命令位置和當前位置數值分歧即可，留意設置時傳送帶上不要有玻璃。
First turn on the air pump switch, power supply switch, console switch, press the manual button in the console, then find the origin setting on the display screen, click on the auxiliary origin setting, then click on the origin setting of the head, pay attention to the origin setting to prevent the head and auxiliary sucker collision. After setting, return to find the glass thickness setting, first the glass thickness, then the aluminium partition, then the glass thickness. After input, click Settings to enter. Just wait for the command position and the current position to diverge. Be careful not to have glass on the conveyor belt when setting.
然后是混交了，按桶膠按鈕，按工作選擇按鈕，然后按拍膠啟動，在按伐開，此時膠頭以出膠，等看不見白膠，以混平均以后按伐關，在按鏈接消費線，自動，自動運轉，此時能夠自動打膠。
Then mix, press the first bucket of glue button, press the work selection button, then press the tap glue to start, in the cut, at this time the glue head to glue, etc. can not see the white glue, after mixing average, press the cut off, in the link consumption line, automatic, automatic operation, at this time can automatically glue.
開端打膠要看每條邊每個角打膠能否平均，下面說下如何調整打膠機，在屏幕上點擊返回找到密封配方，點擊進入，會顯現當前密封壓力，假如每條邊都缺膠，那么可增加壓力，壓力大膠量大，壓力小膠量就小。
Start gluing depends on the average gluing at each corner of each side. Here is how to adjust the gluing machine. Click back on the screen to find the sealing formula. Click in, it will show the current sealing pressure. If there is a lack of glue on each side, it can increase the pressure. Large amount of pressure glue, small amount of pressure glue.

下面說下針對某條邊，或某個交，膠量不夠的調試辦法。在點擊密封配方進入后會顯現有向上密封，上部密封，向下密封，和下部密封，開端打膠的那條邊就是向上密封，然后次第從上。
The following is the debugging method for a certain edge, or a certain intersection, the glue content is insufficient. After clicking on the sealant formula, there will be upward seals, upper seals, downward seals, and downward seals. The first side of the sealant is upward seals, and then from the top.
假如先打膠的這條邊，打膠不平均，那么點擊向上密封，進入后顯現。掃描器開后發開的時間，就是在膠嘴貼到玻璃開端挪動膠嘴出膠的時間，時間長出膠晚，時間短出膠早，掃描器開后開端挪動的時間，就是膠嘴挪動的速度，時間長挪動慢，出膠多，時間短挪動快出膠少
If the edge of the first gluing is uneven, then click on the upward seal and appear after entering. The opening time of the scanner is the time when the glue nozzle is moved from the glue nozzle to the beginning of the glass. The longer the glue nozzle is, the earlier the glue is. The time when the scanner starts moving after the opening of the scanner is the speed of the glue nozzle moving. The longer the time is, the slower the glue is moved, the more the glue is released, and the shorter the time the faster the glue is moved, the faster the glue is released.
掃描膠量細微調整，就是只要某條邊膠少，或多，時調整掃描膠量細微調整，數值大膠量就大，數值小膠量就小。然后說下到末端伐關的間隔，數值大，膠嘴到末端膠量少，數值小膠量大。拐角時伐開的時間，就是控制拐角的膠量，數值大膠量大，數值小膠量小。假如拐角膠多就調小數值，拐角膠少，數值加大
Fine adjustment of scanning glue quantity means that as long as a certain edge glue is less or more, fine adjustment of scanning glue quantity will result in large value glue quantity and small value glue quantity. Then, the interval from the end to the end of the cut-off is large, the glue amount from the nozzle to the end is small, and the glue amount from the end is large. The cutting time at the corner is to control the glue quantity at the corner. The value is large, the value is small and the glue quantity is large. If there is more corner glue, the value will be reduced. If there is less corner glue, the value will be increased.
感謝您的閱讀與觀看，更多關于中空玻璃打膠的詳情，歡迎關注我們的官網：http://www.txxfj.com，我們會有更多的精彩內容繼續為您呈現，謝謝大家的支持！
Thank you for your reading and watching. More details about gluing hollow glass. Welcome to our official website: http://www.txxfj.com. We will have more wonderful content to continue to show you. Thank you for your support!