臥式中空玻璃設備包括玻璃清洗機和玻璃涂布機設備等中空玻璃加工設備，其中，玻璃涂布機設備主要作用就是將丁基膠加熱后，均勻打在鋁隔條的兩側，倘若玻璃涂布機設備出來的膠不均勻，會是什么原因呢？昌盛機械為您介紹幾點：

　　Horizontal insulated glass equipment includes insulated glass processing equipment such as glass cleaning machines and glass coating machines. The main function of the glass coating machine equipment is to heat the butyl rubber and evenly apply it to both sides of the aluminum spacer. If the glue produced by the glass coating machine equipment is uneven, what could be the reason? Changsheng Machinery would like to introduce a few points to you:

　　玻璃涂布機設備的膠嘴

　　Glue nozzle of glass coating machine equipment

　　一、玻璃涂布機設備的膠嘴堵了。倘若一個膠嘴出膠正常，一個偏少，一般就是膠嘴堵，有很多原因造成，比如，放丁基膠時沒有除掉外面的塑料膜，或者放置丁基膠時有砂石之類的，都會造成膠嘴堵塞，最簡單的處理方法就是用個細的鐵絲，捅一下膠嘴就行了；

　　1、 The nozzle of the glass coating machine equipment is blocked. If one nozzle produces glue normally and one is insufficient, it is usually due to nozzle blockage. There are many reasons for this, such as not removing the plastic film outside when placing butyl rubber, or having sand and gravel when placing butyl rubber, which can cause nozzle blockage. The simplest solution is to use a thin wire to poke the nozzle;

　　二、玻璃涂布機設備的膠嘴加熱的加熱棒壞了。丁基膠在常溫下是固態的，只有升溫至120度以上才會變成能夠流動的液態，倘若膠嘴加熱的加熱棒壞了，肯定會造成丁基膠膠嘴出膠少甚至不出膠，聯系廠家，發一個加熱棒換上即可。

　　2、 The heating rod for heating the nozzle of the glass coating machine equipment is broken. Butyl rubber is solid at room temperature and only becomes a liquid that can flow when heated above 120 degrees Celsius. If the heating rod used to heat the rubber nozzle is broken, it will definitely cause the butyl rubber nozzle to produce less or even no glue. Contact the manufacturer and send a heating rod to replace it.

　　三、玻璃涂布機設備的油壓過低或者油量過少。油量顯示，是在油桶邊上有個透明塑料管，采用連通器的原理看到油桶里面的油量，一般在操作面板上有油壓顯示表，一般7-8公斤就完全可以生產了，油壓太低，出膠不均勻，油壓太高，密封墊會漏膠。切記！

　　3、 The oil pressure or quantity of the glass coating machine equipment is too low. The oil level display is a transparent plastic tube on the edge of the oil drum, which uses the principle of a connector to see the oil level inside the drum. Generally, there is an oil pressure display gauge on the operation panel, and 7-8 kilograms can be produced completely. If the oil pressure is too low, the glue output will be uneven, and if the oil pressure is too high, the sealing gasket will leak glue. Remember!

　　基本就這三種造成玻璃涂布機設備的出膠不均勻，倘若還有其他疑問，請聯系昌盛機械，我們一起探討解決。

　　Basically, these three reasons cause uneven glue dispensing in glass coating equipment. If you have any other questions, please contact Changsheng Machinery and we will discuss solutions together.

　　玻璃清洗機和玻璃涂布機設備等臥式中空玻璃設備，昌盛機械是專業的，請相信專業的力量！

　　Changsheng Machinery specializes in horizontal insulated glass equipment such as glass cleaning machines and glass coating machines. Please believe in the power of professionalism!

　　本文由    玻璃涂布機設備      友情奉獻.更多有關的知識請點擊  http://www.txxfj.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from glass coating machine equipment For more related knowledge, please click http://www.txxfj.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.