臥式中空玻璃打膠機Y型過濾器的位置在輔料泵出口處，清洗時將端蓋擰下，用煤油浸泡，用牙刷類刷子刷干凈。安裝時將網放在端蓋里用手擰到底，再用扳手擰緊。用一組膠洗一次，如無雜質兩組膠洗一次，靈活掌握。

　　The position of the Y filter is at the exit of the auxiliary pump. When cleaning, the end cover is screwed down, the oil is soaked with kerosene, and the brush brush is used. The installation will be placed on the end cover by hand net screwed in the end wrench, tighten. Use a group of glue to wash once, such as no impurity two groups of glue washing once, flexible mastery.

　　當膠流速變慢或者混膠不均時清洗混合器。將混合器拆下橫放在臺鉗上，夾住兩端蓋，不要夾到螺絲。用六角扳手松開兩端的六條螺絲，打開器體，取出墊片，擋針，混合芯。將各個零件清洗干凈。端蓋不要弄變形，各個平面不要有劃傷。

　　The mixer is cleaned when the flow rate is slow or the glue is uneven. The mixer remove across the vise, clamped at both ends of cover, not to screw clamp. Release the six screws at both ends with a six angle wrench, open the body, remove the gasket, the needle, and the mixed core. Clean the parts. Do not deform the cover, and do not have any scratches in each plane.

　　混合器一端有凹槽，安裝時將其放進有擋針孔的一面，將擋針放入擋針孔，橫放在凹槽上。更換好墊片后將端蓋對準器體，A對A，P對P，擰上螺絲，擰好后橫放在臺鉗上夾緊，用扳手擰緊下端的四條螺絲，松開臺鉗，器體旋轉300°，夾緊臺鉗，再擰緊下面四條螺絲。依次擰四五次即可。按A面進口，P面出口安裝到膠機上即可。

　　The mixer end is provided with a groove, the installation will be put into the side of retaining the pinhole, will stop into the retaining needle pinhole, across the groove. Replace gasket after the end cap aligner, A to A, P to P, screw, screw after lying in a vise clamped by four screws, the lower end of the wrench to tighten loose vise device body is rotated 300 degrees, and then tighten the clamping vise below four screws. Turn four or five times in turn. According to the A surface, the P surface is installed on the glue machine.

　　清洗時將其擰下，用尖嘴鉗擰下小螺母，拔出針體，彈簧。全部清洗干凈。針閥出口平面及針帽確保無任何雜質，劃傷，變形。安裝時將針插入閥體，彈簧套在針體上，螺母大頭向里面擰緊，力量在1到2公斤左右。

　　When cleaning, unscrew the nut with a small clamp screw, pull out the needle body, spring. Clean up all. Needle valve outlet plane and needle cap to ensure no impurities, scratch, deformation. When installed, the needle is inserted into the body. The spring is set on the body of the needle and the nut head is tightened to the inside. The force is about 1 to 2 kilograms.

　　臥式中空玻璃打膠機臥式中空玻璃打膠機臥式中空玻璃打膠機大過濾器的位置在高壓表B表右下，擰下回流閥下方膠管，擰下過濾器，將網及網芯取出，彈簧、取出，刷干凈，將彈簧小孔套在網芯的凸點上。倒著裝入器體后轉過來擰在膠機上。用3-5組洗一次，如無雜質，靈活掌握即可 。

　　A horizontal hollow glass glue machine horizontal hollow glass glue machine horizontal hollow glass glue filter machine position in the high table B table right, unscrew the valve below the hose, unscrew the filter, the net core removal, spring, spring will be removed, cleaned, small core convex set in the network point. Reverse the loader body and turn it on the glue machine. Use 3-5 groups of washing, such as no impurities, flexible mastery.

　　以上便是雙組份打膠機今天的分享，您還滿意嗎，歡迎關注我們的網站:http://www.txxfj.com并且關注我們的產品，我們將為您提供優良的產品，衷心的愿與您建立合作關系。

　　The above is a two component glue machine today's sharing. Are you satisfied? Welcome to our website: http://www.txxfj.com and pay attention to our products. We will provide you with excellent products and sincerely cooperate with you.