雙組份打膠機供膠系統的清洗我們要把所有的管路閥門都拆解下來，拆解方法非常的簡單用一般的扳手即可完成!

　　The cleaning of the glue system of the two-component glue machine, we must first disassemble all the pipeline valves, disassemble the method is very simple, can be completed with a general wrench!

　　當膠流速變慢或者混膠不均時清洗混合器。將混合器拆下橫放在臺鉗上，夾住兩端蓋，不要夾到螺絲。用六角扳手松開兩端的六條螺絲，打開器體，取出墊片，擋針，混合芯。將各個零件清洗干凈。

　　Cleaning mixer when the flow velocity of gum is slow or uneven mixing. The mixer remove across the vise, clamped at both ends of cover, not to screw clamp. Loosen the six screws at both ends with the six angle wrench, open the body, remove the gasket, stop the needle, and mix the core. Clean all parts.

　　端蓋不要弄變形，各個平面不要有劃傷。混合器一端有凹槽，安裝時將其放進有擋針孔的一面，將擋針放入擋針孔，橫放在凹槽上。

　　Do not deform the end cover, do not scratch each plane. The mixer end is provided with a groove, the installation will be put into the side of retaining the pinhole, will stop into the retaining needle pinhole, across the groove.

　　更換好墊片后將端蓋對準器體，A對A，P對P，擰上螺絲，擰好后橫放在臺鉗上夾緊，用扳手?jǐn)Q緊下端的四條螺絲，松開臺鉗，器體旋轉300°，夾緊臺鉗，再擰緊下面四條螺絲。依次擰四五次即可。按A面進口，P面出口安裝到膠機上即可。

　　Replace gasket after the end cap aligner, A to A, P to P, screw, screw after lying in a vise clamped by four screws, the lower end of the wrench to tighten loose vise device body is rotated 300 degrees, and then tighten the clamping vise below four screws. Turn it four or five times in turn. According to the A surface import, P surface outlet installed on the glue machine can.

　　打膠機Y型過濾器的位置在輔料泵出口處，清洗時將端蓋擰下，用煤油浸泡，用牙刷類刷子刷干凈。安裝時將網放在端蓋里用手?jǐn)Q到底，再用扳手?jǐn)Q緊。用一組膠洗一次，如無雜質兩組膠洗一次，靈活掌握。

　　The position of Y type filter is at the outlet of auxiliary pump, and the end cover is screwed down when washing. It is soaked with kerosene and cleaned with toothbrush brush. The installation will be placed on the end cover by hand net screwed in the end wrench, tighten. Use a set of glue to wash once, such as no impurities, two groups of rubber wash once, flexible grasp.

　　清洗時將其擰下，用尖嘴鉗擰下小螺母，拔出針體，彈簧。全部清洗干凈。針閥出口平面及針帽確保無任何雜質，劃傷，變形。安裝時將針插入閥體，彈簧套在針體上，螺母大頭向里面擰緊，力量在1到2公斤左右。

　　When cleaning, unscrew the nut with a small clamp screw, pull out the needle body, spring. Clean all. Needle valve outlet plane and needle cap ensure no impurities, scratches, deformation. When installing, insert the needle into the valve body, the spring is sheathed on the needle body, the nut is screwed to the inside, and the power is about 1 to 2 kilograms.

　　打膠機大過濾器的位置在高壓表B表右下，擰下回流閥下方膠管，擰下過濾器，將網及網芯取出，彈簧、取出，刷干凈，將彈簧小孔套在網芯的凸點上。倒著裝入器體后轉過來擰在膠機上。用3-5組洗一次，如無雜質，靈活掌握即可 。

　　The position of the big filter of the glue machine is in the right lower part of the B table of the high-pressure meter, the rubber hose below the reflux valve is screwed, the filter is screwed down, the net and the net core are taken out, the spring is taken out, the brush is cleaned, and the spring hole is sheathed on the convex point of the net core. Turn it upside down and load it on the rubber machine. Wash with 3-5 groups, such as no impurities, flexible control can be.

　　打膠機膠槍的槍口混合器清洗時直接擰下槍口混合器取出混合芯即可。清洗槍柄混合器時，先把槍上的定位螺絲松開，然后擰下槍柄混合器。槍口混合器同混合器同周期清洗;搶柄混合器同槍同周期清洗，半年或一年洗一次。

　　The muzzle mixer of the glue gun of the glue machine is directly screwed off the muzzle mixer when the cleaning is done, and the mixing core can be removed. When the first mixer cleaning grips, positioning screws loose on the gun, then unscrew the grips mixer. The muzzle mixer is cleaned with the same period of the mixer; the grab mixer is cleaned with the same period of the gun, and washed once or half a year.

　　以上便是雙組份打膠機今天的分享，您還滿意嗎，歡迎關注我們的網站:http://linshi.jncsjx.com/并且關注我們的產品，我們將為您提供優良的產品，衷心的愿與您建立合作關系。

　　The above is to share the two-component glue machine today, you still satisfied with it, welcome to our website: http://linshi.jncsjx.com/ and pay attention to our products, we will provide you with excellent products, sincerely wish to establish business relationship with you.